Sunday, January 27, 2008

Change / Replace The Belt on a Treadle (pedal) Sewing Machine


Although it may initially look complicated to change the long leather belt on a treadle (pedal) sewing machine, it's actually very simple, and can easily be done by the average person using tools that are common around most households. My directions will seem more complicated than the procedure actually is.


Tools needed; a sharp knife or large scissors, an ink pen or Sharpie marker, a 4d-6d finish nail or a sharp ice pick or punch about the diameter of a pencil lead. A pair of pliers.


Clip the old belt in two (if it's still present) These belts generally last a long, long time under the right conditions. I have seen 100 year old treadle belts that still worked! However, they eventually dry-rot or just break.


The machine should be in the up (working) position.


Fold the new belt in the middle, and place it over the top of the handwheel of the machine. There will be two holes on most machine's cabinets directly under the handwheel, and immediately to the right of the machine base. Half the new belt goes in the front hole, and half in the back hole. Push it all the way down so that it comes down over the handwheel and lays in the belt groove, which will be to the left of where you grasp the handwheel, and be smaller in diameter. You may have to work the belt around the bobbin winder or belt guard to get it into the right place.


Now get on your knees and peer up underneath the cabinet. You will of course see the two long ends of the belt that you just pushed through from above. The object is to get the back half looped around the large pulley underneath, and pulled up toward the front of that pulley so it can be measured and marked. This takes a little doing, especially the first time. No, no, go ahead and get the belt on and don't stop to clean out all the dust and cobwebs that you see under there!


On some machines there will be metal loops immediately above the front and back of that large pulley that the belt must go through before looping around the pulley for measuring. Most Singer machines only had one hinged loop in front. Be sure the belt gets through the loop(s) Then work the back half of the belt around the back and bottom of the large pulley. To get it all the way around you will have to pull it farther down and give some slack on the front half of the belt.


Being sure the belt is still correctly around the machine handwheel, and that it's looped around the large pulley underneath, and through all the loops and holes it's supposed to go through, then pull it up snug, let the ends lap, and mark the end that does not have the metal staple in it.


Some folks take the belt back off at this point, others just work with it while on their knees. You'll have to at least flip it loose from the large pulley to give yourself some working slack. Cut the excess belt off at your mark. on most machines you'll wind up cutting off about 4"-8" of belt. Note how that metal staple is fastened in to the other (uncut) end, and punch a corresponding hole in the cut end of the belt. Try to get the hole centered in the belt material.


Put the belt back in place, hook the staple through the hole you just punched, then using your pliers pinch the open end of the staple down onto the belt. You've done it!


The goal is to have the belt tight enough so that it doesn't slip much, but not so tight that it makes the machine difficult to pedal. After a few months you may have to clip some more off, as the leather may stretch some. After that, it will be good for decades!


We carry a supply of good quality treadle belts in our online catalog at http://www.vintagesingersewing.com/. We also have bobbins and shuttles for a lot of the old machines.

Bernina 830 & 930; Don't Try These At Home!


Bernina 830 & 930
PROBLEMS YOU PROBABLY SHOULD NOT TACKLE ON YOUR OWN


Unbalanced Buttonhole- If stitch density on one side of the buttonhole is tighter or looser than the other side, and you are using the correct foot and technique. This is a very painstaking adjustment that requires a special tool.

Machine is dead- If your machine’s light works OK, but the machine will not run, you probably will want to take it to a service person who can diagnose the exact problem. It’s expensive to replace parts at random.

Motor Noises- Any unusual noise (buzzing, growling, squeaking, grinding, etc.) is indicative of a problem that is not just going to go away. It will probably get worse although you may continue to use it for some time.

Major Breakage- It is very common for a machine to fall off the table, be damaged in transit, or meet with some other misfortune. If a major body part, such as the handwheel, bobbin winder, take-up lever, pressure lifter, etc. is broken, then it’s a job for a repairman.

Tight Spot- When turning the machine by hand, if it gets suddenly tighter at the same spot in its revolution, and there is not thread caught around the take-up assembly or handwheel, then the news could be bad.

Timing- When the upper thread will not loop around the bobbin or pull up the bobbin thread, or a new straight needle hits or catches something down in the machine then it’s usually a "timing" problem. There are several interrelated adjustments to be made in this event, and I do not believe it should be tried at home. The potential for doing more damage is too great for someone without experience in sewing machine repair.

Friday, January 11, 2008

#1 Problem with the 221/222 Singer Featherweight

#1 MOST COMMON PROBLEM: NEEDLE INSERTION


The Featherweight uses the common needle type which goes by several different designations; 15X1, 705, etc. These come in sizes from 8 (smallest) to 19 (largest). The “size” refers to the thickness of the needle, and not the length. All modern household machines, Featherweight included, use the same length needle.


The critical difference between the Featherweight and most other machines is that the NEEDLE IS INSERTED WITH THE FLAT SIDE OF THE NEEDLE TO THE OPERATORS LEFT. (Illustrated above) Unless the needle is inserted correctly the MACHINE WILL NOT SEW. Certainly you must also be sure your needle is not bent or blunted. Better to dispose of a questionable needle than take a chance

Although the Singer “color-coded” needles are suitable, I prefer the Schmetz brand for quality. Any others should be avoided.
This post seems really basic, but I have seen many hundreds of Featherweights which would not sew because the needle was inserted incorrectly.
For a wide selection of parts for vintage Singer, Pfaff, or Bernina machines see our website www.vintagesingersewing.com